Nodor IPS 37 Spécifications télécharger pdf (Page 7)

THIS APPLIANCE IS DESIGNED FOR DOMESTIC USE ONLY.

THE MANUFACTURER SHALL NOT IN ANY WAY BE HELD

RESPONSIBLE FOR WHATEVER INJURIES OR DAMAGES ARE

CAUSED BY INCORRECT INSTALLATION OR BY UNSUITABLE,

WRONG OR ABSURD USE.

The manufacturer declares that this product meets all basic

requirements regarding low-voltage electrical equipment established

in the 2006/95/EEC Directive of 12 December 2006 and electro-

magnetic compatibility established in 2004/108/EEC Directive of 15

December 2004.

The operating principle (Fig. 1)

It operates thanks to electromagnetic properties and can be used

with the majority of cooking pans.

The electronic circuit governs the operation of the coil (inductor)

which creates a magnetic field.

Heat is transmitted from the pan to the food contained within.

Induction cooking has the following characteristics:

- Minimal dispersion (high performance).

- Removing (or lifting) the pan from the hob automatically stops the

cooking zone.

- The electronic system permits flexibility and precision control.

(Fig. 1)

1 Pan

2 Induced current

3 Magnetic field

4 Inductor

5 Electronic circuit

6 Electric power supply

Instructions for the user (Fig.2)

1 ON/OFF

2 Sliding control

3 Power level display

4 Automatic pre-heating indicator

5 Timed zone indicator

6 Active Keep Warm function indicator

7 Keep Warm function

8 Timer

9 Timer display

10 Lock

11 Active lock indicator

Installation

All operations relating to installation (electrical connection) must be

carried out by qualified personnel in line with current regulations.

See the part reserved for fitters for specific instructions.

Functionality Slider TC:

Slider: sensor technology of the novel Slider TC allows as well an

adjustment of the cooking levels (1 – 9) as the timer value (1-99) by

touching and pulling the finger over the designated area. Pulling to

the right is increasing and to the left is decreasing accordant value.

Moreover a direct selection of the designated value is also

possible on the slider area.

Switching the Touch Control on/off

After mains voltage is applied, the touch control initialises for

approximately one second before it is ready for use. All displays and

LEDs flash for approximately one second after resetting. Once this

period is complete, all displays and LEDs switch off and the touch

control is in standby mode.

Press the ON/OFF (1) button to switch the touch control on for 1

second. The cooking zone displays indicate “0”. If a cooking zone is

in “hot” (high temperature) mode, the display will read “H” instead of

“0”.

After switching the touch control on, it will remain active for 10

seconds. If neither a cooking zone nor the timer function is selected,

the Touch control automatically returns to standby mode.

The touch control is only turned on by pressing the power button. If

the power button is pressed at the same time as other buttons, no

action is taken, and the touch control remains in stand-by mode.

The touch control can be switched off at any time using the power

button. This is even the case when the control has been locked by

the child safety feature. The power button always takes priority in the

switching off function.

Switching a cooking zone on/off

When the Touch Control is turned on, any of the cooking zones can

be activated by pressing on the corresponding slide control, (2). By

pressing and sliding the finger across the slide control, (2), it is

possible to select a setting level in the range of 0 to 9. The setting

level is shown in the corresponding display, (3).

To switch off the cooking zone, just select setting level 0 by pressing

the corresponding sliding control. If the residual heat of the cooking

zone is high, the corresponding display, (3), shows an “H”.

Place the pan on the appropriate cooking zone. If the pan is not in

place, the system will not activate the corresponding zone and the

following symbol is displayed:

Switching Off all cooking zones

Immediately switching off all cooking zones is always possible by

using the ON/OFF key. ”H” possibly appears on all hot cooking

zones. All other cooking zone displays remain black.

Automatic preheating

This simplifies the cooking process as it is not necessary to

supervise the whole cooking cycle. The function establishes

preheating of the cooking zone at maximum power to take the zone

to the system temperature quickly. After a certain time, the setting

level returns to the programmed level.

Activation of automatic preheating

In the required zone, select the setting level for the cooking on the

sliding control (2), and hold down for 3 seconds. The symbol “A”

alternates in display (4).

1 2 3 4 5 6 7 8 9 10 11 12 ... 39 40

CATA ELECTRODOMÉSTICOS, S.L 40

Commentaires sur ces manuels

Pas de commentaire

Nodor IPS 37 Spécifications Page 7

Commentaires sur ces manuels